Motorola LS6000B-U Betriebsanweisung Seite 29
- Seite / 180
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
LS 6000 Scintillation System User’s Manual
PN 247971-F
2-11
Getting Started
Preparing the Printer
2
To set up the Sample Rack(s), select any of the supplied racks other than the color-coded
racks. Insert the desired User Number Card as a Command Card onto the rack as described
above. Continue to make other Sample Racks by placing a User Number Card in the slot.
Place a Rack Number Card on the racks with User Number Cards and any other racks you
will use for counting samples. Refer to Section 3.2 for more information on using the Sample
Racks.
Installing the Racks
For counting, the racks are placed in the sample changer (the bed of the instrument which
transports the samples). The racks are moved in a counter-clockwise motion. The vials are
counted when the rack has reached the right rear position where the elevator that moves the
vial into the counting chamber is located.
To install a rack, hold it so that the molded position numbers are toward you, and the cards
(if any) face away from you. Place the rack on the right side of the sample changer, inserting
it at an angle so that the lip on the left end slides under the groove along the middle of the
sample changer. See Figure 2.6. After installing the rack, push it away from you, toward the
back of the sample changer where the elevator is located.
Since the racks are moved in a counter-clockwise direction, the second and successive racks
are installed progressively toward the front of the instrument. When the right-hand side of
the sample changer is filled, load additional racks on the left-hand side, front to rear. The
racks on the left side are also loaded with the molded numbers toward you, cards (If any)
away from you. Slide the lip on the left end of the rack under the groove along the left side of
the sample changer.
2.5 Preparing the Printer
The printer is set up at the time of installation by your Beckman Service Representative.
Details of the printer operation are provided in the printer manual that was delivered with
your instrument.
Figure 2.6 PLacing the Rack In The Sample Changer
- LS 6000 Series 1
- Table of Contents 3
- Introduction 11
- Principles of Operation 12
- Operating the Instrument 12
- Operating Modes 13
- 1.3 Specifications 14
- Precautions and Limitations 15
- Figure 1.1 Standard Vial 15
- Miniature Vials 16
- 1.5 Hazards 17
- Maintenance 18
- Getting Started 19
- 2.2 Power Failure 21
- 2.3 Operating Controls 21
- Operator Control Key pad 22
- Using the Operating Controls 24
- 2.4 Using the Racks 25
- Using the Racks 26
- Setting Up the Racks 27
- 2.5 Preparing the Printer 29
- 2.6 System Setup 30
- Energy Scale 31
- Printer Paging 32
- Allow Interrupt Count 32
- System Setup 33
- Figure 2.9 RS232 Setup Menu 33
- Date/Time 35
- Auto DPM 35
- 2.7 Calibration 36
- Counting Samples 39
- Starting the Automatic Count 40
- Conducting Count Single Rack 41
- 3.4 Auto DPM 46
- 3.5 Multi-Task 47
- Interrupt Count in Multi-Task 48
- Multi-Task 50
- Interrupt Data 51
- Setting Up User Programs 59
- 4.2 Editing A User Program 61
- Editing A User Program 62
- Comments 65
- Counting Time 65
- Liquid or Xtal Scintillator 65
- Isotope 1 65
- Isotope 2 and Isotope 3 66
- Edit Other Parameters 67
- Counting Precision 69
- Background/Blank Subtraction 69
- Lum-Ex Correction 71
- Phase Monitor 72
- Low Level 72
- Low Count Reject 72
- Output Formats 72
- Count Data 75
- Raw Data 75
- Collecting Spectral Data 76
- 4.3 Copy User Program 77
- Copy User Program 78
- 5.2 CPM/Xtal CPM 80
- CPM/Xtal CPM 81
- Results for CPM/Xtal CPM 83
- 5.4 Auto DPM 85
- Setting Up Auto DPM 86
- Loading Samples for Auto DPM 86
- Results for Auto DPM 86
- Setting Up DPM 87
- 5.6 Xtal DPM 89
- Xtal DPM 90
- Setting Up Xtal DPM 91
- Loading Samples for Xtal DPM 92
- 5.7 DPM % of Reference 93
- Setting Up DPM % of Reference 94
- Xtal SL DPM % of Reference 95
- 5.9 Single Photon Monitoring 98
- Data Calculation 100
- Single Photon Monitoring 100
- Isotope/DPM Libraries 103
- Accessing the Isotope Library 104
- Printing the Isotope Library 104
- The Isotope Library 105
- Setup Menu 106
- PN 247971-F 108
- 5 minutes 109
- 6.2 Setting Up A Quench Curve 110
- Setting Up A Quench Curve 112
- Counting the Standards 114
- Editing Quench Curves 120
- Deleting A Quench Curve 124
- Manual Entry of Quench Curves 125
- 7.1 Chemiluminescence 127
- Interpretation of Results 128
- Reducing Single Photon Events 128
- 7.3 Two Phase Samples 129
- Procedures 131
- Analysis of Data 131
- H Counting Efficiency 132
- C Counting Efficiency 132
- Background 133
- Contamination 133
- Instrument Specifications 135
- Temperature Control Accessory 138
- Installation Requirements 139
- Electrical Requirements 140
- 0.5 to 1.0 m in 140
- Environment Requirements 142
- . Note that the output 144
- Datum IDs 146
- CHAPTER 1, PART 31 167
- Region I 170
- Region II 170
- Region III 170
- Region IV 170
Verwandte Produkte und Handbücher für Barcodeleser Motorola LS6000B-U
Barcodeleser Motorola SYMBOL MS320X Spezifikationen
(428 Seiten)
(428 Seiten)
Barcodeleser Motorola SB1 Betriebsanweisung
(82 Seiten)
(82 Seiten)
Barcodeleser Motorola MC17T Bedienungsanleitung
(24 Seiten)
(24 Seiten)
(32 Seiten)
Barcodeleser Motorola MP6000 Spezifikationen
(200 Seiten)
(200 Seiten)
Barcodeleser Motorola DS9208-1D Spezifikationen
(380 Seiten)
(380 Seiten)
Barcodeleser Motorola SYMBOL LS7708 Spezifikationen
(380 Seiten)
(380 Seiten)
Barcodeleser Motorola WT4090 Spezifikationen
(206 Seiten)
(206 Seiten)
(2 Seiten)
Barcodeleser Motorola LS1000B Spezifikationen
(96 Seiten)
(96 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.607 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern