Motorola LS6000B-U Bedienungsanleitung

Laser Barcode Scanner User’s ManualPDF created with pdfFactory Pro trial version www.pdffactory.com

8 Multiscan Functions – 1 OUTPUT FIRMWARE VERSION RESET CONFIGURATION TO DEFAULTS 0A 0B OUTPUT MODE – KEYBOARD WEDGE OUTPUT MODE OUTPU

9 Multiscan Functions – 2 DECODE OPTIONS REVERSE IMAGE – ENABLE IMAGE DECODE OPTIONS REVERSE IMANGE - DISABLE 01391 01390 DECODE OPTIONS

10 Interface – KBW WEDGE MODE - AUTODETECT PC Communication WEDGE MODE – SCAN SET 2 PASS THRU 000200 000204 TRANSMIT SPEED - 0 TRANSMI

11 Interface – Serial - 1 SERIAL BAUD RATE - 2400 BAUD RATE SERIAL BAUD RATE - 4800 000703 000704 SERIAL BAUD RATE - 9600 SERIAL BAUD RA

12 Interface – Serial - 2 SERIAL DATA BITS - 8 PARAMETERS SERIAL DATA BITS - 7 00081 00080 SERIAL STOP BITS - 1 SERIAL STOP BITS - 2 00

13 Interface - WAND CODE 128 WAND EMULATION – ENABLE CODE 128 WAND EMULATION - DISABLE 00141 00140 WAND EMULATON SPEED – FASTEST (0) SPEED

Symbologies On/Off - 1 CODE 93 - ENABLE CODE 93 CODE 93 - DISABLE 00621 00620 CODE 128 - ENABLE CODE 128 CODE 128 - DISABLE 00691 00690

1 MSI - ENABLE MSI/PLESSEY MSI - DISABLE 01151 01150 UPC-A ENABLE UPC/EAN UPC-A DISABLE 00341 00340 UPC-E ENABLE UPC-E DISABLE 00351

2 Symbologies Set Up - 1 CODE 11 ID CHARACTER – “m” CODE 11 CODE 11 ID CHARACTER – “Z” 0131m 0131Z CODE 11 LASER/CCD REDUNDANCY - ENABLE

3 Symbologies Set Up – 2 CODE 93 ID CHARACTER – “h” CODE 93 CODE 93 ID CHARACTER – “Z” 0066h 0066Z CODE 93 LASER/CCD REDUNDANCY - ENABLE C

FCC Compliance This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Ru

4 Symbologies Set Up – 3 CODABAR ID CHARACTER –‛k’ CODABAR CODABAR ID CHARACTER –‛Z’ 0094k 0094Z CODABAR LASER/CCD REDUNDANCY - ENABLE CO

5 Symbologies Set Up – 4 MSI ISBN ID CHARACTER –‛f’ MSI/PLESSEY MSI ISBN ID CHARACTER –‛Z’ 0053f 0053Z MSI LASER/CCD REDUNDANCY - ENABLE

6 Symbologies Set Up – 5 UPC-E ID CHARACTER –‛c’ UPC/EAN UPC-E ID CHARACTER –‛Z’ 0050c 0050Z EAN-13 ID CHARACTER –‛e’ EAN-13 ID CHARACTER

7 Symbologies Set Up – 6 UPC/EAN LASER/CCD REDUNDANCY ENABLE UPC/EAN UPC/EAN LASER/CCD REDUNDANCY DISABLE 00541 00540 PDF created with pdfFa

8 EDIT SETUP BAR CODES EDIT #1 – STRIP 1 LEADING CHARACTER ON ALL BAR CODES THAT START WITH ‛12345’ EDIT #1 - OFF 02000101000000100000000112

9 MACRO/SPECIAL KEYS SETUP BAR CODES MACRO #1 – FIND ‛1’ AND REPLACE WITH ‛ONE’ MACRO #1 - DISABLED 02010101011ONE 0B20101 MACRO #2 – FI

10 TERMINATION STRING SETUP BAR CODES STRING #1 – TERMINATION CHAR - CR STRING #1 – TERMINATION - LF 0202011000$0D 0202011000$0A STRING #1 –

11 Factory Default Setting PDF created with pdfFactory Pro trial version www.pdffactory.com

12 Scanner Timing Default RS-232 communication Default Baud rate 9600 Parity None Data Bits 8 Stop Bit 1 RTS/CTS Off Terminator <CR> Ke

13 Appendix-A Troubleshooting & Error Beeps PDF created with pdfFactory Pro trial version www.pdffactory.com

1 Table of Contents 1. INTRODUCTION………………………………………………………………………………..………2 2. INSTALLATION………………………………………………………………………………..…...4 USB Connection

14 a. Problem: Nothing happens when I follow the operating instructions. Possible Cause Possible Solution Interface cables are loose Check for lo

15e. Problem: The decoder beeps, but no data is displayed on my computer. Possible Cause Possible Solution Decoder is not programmed for the correc

16g. Problem: Some of the barcode data is missing displayed on the host. Possible Cause Possible Solution The decoder’s transmit speed is too fast.

PDF created with pdfFactory Pro trial version www.pdffactory.com

2 Introduction PDF created with pdfFactory Pro trial version www.pdffactory.com

3 Laser barcode scanner combines the best scanning performance and value. The device provides an accurate, easy, and fast method of data entry and

4 Installation PDF created with pdfFactory Pro trial version www.pdffactory.com

5 Insert the plug on the free end of the Communications Cable into the appropriate connector on the host as below described: 1. USB Connection

6 3. RS232 Connection NOTE: for Serial port (RS232 cable), please plug the power connector of 5V power adapter to RS232 cable. 1. Be sure that

7 Setup from Bar Code Label PDF created with pdfFactory Pro trial version www.pdffactory.com