Motorola MP6000 Spezifikationen Seite 118
- Seite / 200
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
3 - 32 MP6000 INTEGRATOR GUIDE
ii. Medium MP6000 and short (shelf mount) MP6000: If the platter is not flush, or the MP6000 rocks,
adjust the optional leveling screws to place the device at the correct height. This can be done from
the top of the MP6000, with the tower bezel removed and the tower cover slightly pushed back.
Figure 3-41
Adjusting Leveling Screws
When the platter is flush, its leading edge should be slightly below the checkstand, and the trailing
edge should be slightly above the checkstand.
To ensure smooth scanning, replace the platter, take a steel can (like a soup can), turn it over so
the harsher seam is facing down, and slide the can over the platter in the standard scanning
direction. The can must not catch on the checkstand or the platter when swept across all sections
of the platter, in the correct direction.
4. Route all cables through the checkstand as shown in Figure 3-3
.
5. Connect all cables to the MP6000 and POS, as needed (e.g., scale, Scale Display, Checkpoint antennas,
or Sensormatic coils, POS, CSS, etc.).
6. Power up the MP6000. Upon power up, the MP6000 verifies that all sub-systems, and auxiliary devices
are operational. If a fault condition exists, an error condition displays on the 7-segment display, and the
startup sequence halts. Power cycling is required after rectifying the problem. (See General Error and
Warning Codes on page A-5)
If a scale is present, warm-up time for the scale is 15 minutes (assuming room the temperature is
70° F/20° C).
Leveling Screw Holes
Under Platter
IMPORTANT Leveling screws are an optional accessory for medium size models (15.7 in./39.8 cm) and short size
models (13.9 in./35.3 cm) and can be ordered separately. Accessory kit MX301-SR00004ZZWR
contains four standard-length screws, and accessory kit MX302-SR00004ZZWR contains four
extra-length screws which will protrude 1"-inch (25 mm) below the bottom of the unit. See Figure 1-5
on page 1-11 for the installation location of these screws and for the locations of access holes for
turning the screws from above.
IMPORTANT Most accessories (scale, Scale Display, Checkpoint interlock, Sensormatic coils, Sensormatic
RS-232 cable, CSS, and auxiliary RS-232 scanners) must be installed and connected to the
MP6000 prior to applying power to the MP6000.
- INTEGRATOR GUIDE 1
- Warranty 4
- Revision History 5
- TABLE OF CONTENTS 7
- Table of Contents vii 9
- Table of Contents ix 11
- ABOUT THIS GUIDE 13
- Related Publications 14
- About This Guide vii 15
- FEATURES 17
- Product Overview 18
- Configurations 19
- 1 - 4 MP6000 INTEGRATOR GUIDE 20
- Table 1-1 21
- 1 - 6 MP6000 INTEGRATOR GUIDE 22
- Peripherals 24
- Features of the MP6000 25
- Left Side View 26
- View Under Platter 27
- Leveling Screws 27
- Figure 1-6 28
- Features Summary 29
- 2 - 2 MP6000 INTEGRATOR GUIDE 32
- Programming Management Tools 33
- Connecting a USB Interface 34
- USB Host Parameters 36
- * IBM Table-top USB 37
- USB Device Type (continued) 38
- Figure 2-2 42
- Table 2-2 42
- Figure 2-3 43
- Table 2-3 43
- (see parameter 43
- page 2-32 43
- Connect MP6000 to RS-232 Host 44
- RS-232 Parameters 45
- RS-232 Host Parameters 46
- Table 2-7 48
- Table 2-8 49
- RS-232 Host Types 50
- *Standard RS-232 51
- RS-232 Host Types (continued) 52
- RS-232 Host -NCR Variant 60
- Parameter # 1246 62
- Third Party Scale 67
- Parameter # 1294 67
- Third Party Scale (continued) 68
- Third Party Scale LED Pin 69
- Parameter # 1295 69
- *Active High 70
- Third Party Scale Zero Pin 71
- Parameter # 1296 71
- IBM RS-485 Host Parameters 74
- *None Selected 75
- RS-232 AUX 1 83
- Scale Display Port 83
- RS-232 AUX 2 84
- Checkpoint Interlock 84
- AUX A-B (Stacked USB) 84
- Table 2-15 85
- Table 2-16 85
- INSTALLATION 87
- Site Preparation 88
- Grounding 89
- Liquid Spills and Moisture 90
- Vertical Clearance 90
- Counter Cutout 91
- Ergonomics 91
- Installing Components 92
- Unpacking MP6000 Equipment 93
- Pre-Installation Notes 94
- Required Tools 95
- Secure in Place 97
- Install the Scale Display 98
- Getting Started 100
- Installing 101
- Connecting the USB Cable 105
- Figure 3-23 107
- Figure 3-24 107
- Install the MP6000 /Scale 110
- Figure 3-30 111
- Figure 3-29 111
- Figure 3-31 112
- Figure 3-32 112
- Optional leveling screw kit 112
- MX301-SR00004ZZWR 112
- Figure 3-33 113
- Figure 3-34 113
- Figure 3-35 114
- Figure 3-36 114
- MX301-SR00004ZZWR or 114
- MX302-SR00004ZZWR 114
- Figure 3-37 115
- Figure 3-38 115
- 11.50 in 116
- 292.2 mm 116
- 20.0 in 116
- 506.9 mm 116
- Figure 3-40 117
- Install Sensormatic Coils 119
- Install Checkpoint Antenna 121
- Figure 3-45 122
- Figure 3-46 122
- Installing the Mounting Frame 123
- WITH A SCALE ONLY) 125
- Scale Configurations 126
- Important Notes 127
- Legal Scale Dampening Filter 128
- 4 - 6 MP6000 INTEGRATOR GUIDE 130
- Calibration Success 131
- Calibration Failure 131
- Verification Test 132
- Table 4-5 133
- Table 4-4 133
- Audit Tallies 135
- * Kilograms 136
- Legal Scale Units (continued) 137
- Scale Display Configuration 138
- Parameter # 986 138
- Parameter # 996 140
- * Low Vibration Sensitivity 141
- Parameter # 996 (continued) 142
- Table 4-6 144
- Overview 147
- Controls and Indicators 148
- OPERATING THE SCANNER 5 - 3 149
- Volume/Tone Control Button 150
- Soft Reset Buttons 151
- Single Interval Range Scales 152
- Dual Interval Range Scales 152
- OPERATING THE SCANNER 5 - 7 153
- 5 - 8 MP6000 INTEGRATOR GUIDE 154
- Scan Windows 155
- Operating Modes 156
- Programming the MP6000 156
- USB Staging Flash Drive 157
- Flash DrivesFlash Drives 158
- Loading Cloning Files 159
- Scanning 161
- Weighing Items 162
- Supported EAS Controllers 163
- Sensormatic EAS Hard Tags 164
- OPERATING THE SCANNER 5 - 19 165
- Beeper and LED Conditions 166
- OPERATING THE SCANNER 5 - 21 167
- Table 5-1 168
- OPERATING THE SCANNER 5 - 23 169
- CHAPTER 6 123SCAN2 171
- Requirements 172
- APPENDIX A MAINTENANCE 173
- TROUBLESHOOTING, AND 173
- ERROR CODES 173
- Troubleshooting 174
- Troubleshooting Assistance 175
- A - 4 MP6000 INTEGRATOR GUIDE 176
- Table A-1 177
- Scale Warning Codes 178
- A - 8 MP6000 INTEGRATOR GUIDE 180
- Technical Specifications 181
- B - 2 MP6000 INTEGRATOR GUIDE 182
- Table B-1 183
- B - 4 MP6000 INTEGRATOR GUIDE 184
- APPENDIX C HOST INTERFACE 185
- CHARACTER SETS 185
- RS-232 Character Sets 186
- Table C-1 187
- C - 4 MP6000 INTEGRATOR GUIDE 188
- C - 6 MP6000 INTEGRATOR GUIDE 190
- Table D-1 191
- D - 2 MP6000 INTEGRATOR GUIDE 192
- Numerics 193
- Index - 3 195
- Tell Us What You Think 197
Verwandte Produkte und Handbücher für Barcodeleser Motorola MP6000
Barcodeleser Motorola DS9208-1D Spezifikationen
(380 Seiten)
(380 Seiten)
Barcodeleser Motorola SYMBOL LS7708 Spezifikationen
(380 Seiten)
(380 Seiten)
Barcodeleser Motorola WT4090 Spezifikationen
(206 Seiten)
(206 Seiten)
(2 Seiten)
Barcodeleser Motorola LS1000B Spezifikationen
(96 Seiten)
(96 Seiten)
© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.148 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern