Motorola AP-51XX Bedienungsanleitung Seite 173
- Seite / 698
- Inhaltsverzeichnis
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Network Management
5-25
5. Click OK to return to the NAT screen. Within the NAT screen, click Apply to save any
changes made on the Port Forwarding screen.
6. Click Cancel to undo any changes made on Port Forwarding screen. This reverts all settings
for the Port Forwarding screen to the last saved configuration.
5.2.2 Configuring Dynamic DNS
The access point supports the Dynamic DNS service. Dynamic DNS (or DynDNS) is a feature offered
by www.dyndns.com which allows the mapping of domain names to dynamically assigned IP
addresses via the WAN port. When the dynamically assigned IP address of a client changes, the new
IP address is sent to the DynDNS service and traffic for the specified domain(s) is routed to the new
IP address.
To configure dynamic DNS for the access point:
1. Select Network Configuration -> WAN -> DynDNS from the access point menu tree.
Start Port and End Port Enter the port or ports used by the port forwarding service. To
specify a single port, enter the port number in the Start Port area.
To specify a range of ports, use both the Start Port and End Port
options to enter the port numbers. For example, enter 110 in the
Start Port field and 115 in the End Port field.
IP Address Enter the numerical (non DNS name) IP address to which the
specified service is forwarded. This address must be within the
specified NAT range for the associated WAN IP address.
Translation Port Specify the port number used to translate data for the service being
forwarded.
Forward all
unspecified ports to
Use the Forward all unspecified ports to checkbox to enable
port forwarding for incoming packets with unspecified ports. In the
adjacent area, enter a target forwarding IP address for incoming
packets. This number must be within the specified NAT range for
the associated WAN IP address.
NOTE DynDNS supports only the primary WAN IP address.
- Product Reference Guide 1
- AP-51xx Access Point 3
- Product Reference Guide 3
- Contents 5
- Chapter 3. Getting Started 8
- Chapter 5. Network Management 9
- Chapter 8. CLI Reference 11
- Chapter 10. Adaptive AP 13
- Appendix B. Usage Scenarios 14
- Appendix C. Customer Support 14
- About This Guide 15
- Notational Conventions 16
- Service Information 16
- Introduction 17
- 1.1 New Features 18
- 1.1.2 Rogue AP Enhancements 19
- 1.1.5 QBSS Support 19
- 1.2 Feature Overview 20
- 1.2.8.2 EAP Authentication 25
- 1.2.8.3 WEP Encryption 25
- 1.2.8.4 KeyGuard Encryption 26
- 1.2.8.7 Firewall Security 27
- 1.2.8.8 VPN Tunnels 27
- 1.2.8.9 Content Filtering 27
- 1.2.9 VLAN Support 28
- 1.2.11 Updatable Firmware 28
- 1.2.15 Voice Prioritization 30
- 1.2.17 Statistical Displays 31
- 1.2.18 Transmit Power Control 31
- 1.2.22 DHCP Support 32
- 1.2.23 Multi-Function LEDs 33
- 1.2.24 Mesh Networking 33
- 1.2.25 Additional LAN Subnet 34
- 1.2.27 Hotspot Support 35
- 1.3 Theory of Operations 36
- 1.3.1 Cellular Coverage 37
- 1.3.2 MAC Layer Bridging 38
- 1.3.3 Media Types 38
- 1.3.5 MU Association Process 39
- 1.3.6 Operating Modes 40
- Hardware Installation 45
- 2.1 Precautions 46
- Part No. Description 47
- 2.2.2 AP-5181 Configurations 48
- 2.3 Requirements 49
- 2.4 Access Point Placement 49
- 2.4.1 Site Surveys 50
- 2.4.2 Antenna Options 50
- 2.5 Power Options 53
- 2.5.2 AP-5181 Power Options 54
- 2.7 Mounting an AP-5131 57
- Light Pipe 65
- Ceiling Tile 65
- 2.8 AP-5131 LED Indicators 67
- 2.9 Mounting an AP-5181 68
- Attach the square 69
- 2.10 AP-5181 LED Indicators 73
- Data over Ethernet 74
- 802.11a radio activity 74
- 802.11b/g radio activity 74
- 2.11 Setting Up MUs 75
- Getting Started 77
- 3.2 Configuration Options 78
- 3.5.2 Testing Connectivity 90
- 3.5.3 Where to Go from Here? 91
- 4.2 Adaptive AP Setup 98
- 4.3 Configuring Data Access 101
- System Configuration 103
- 4.5 Configuring SNMP Settings 115
- Feature MIB Feature MIB 116
- SNMP v3 user definitions 119
- SNMP access 122
- 4.5.2 Enabling SNMP Traps 123
- 4.7 Logging Configuration 134
- 4.9 Updating Device Firmware 141
- Network Management 149
- 5.2 Configuring WAN Settings 164
- WAN port 167
- 5.2.2 Configuring Dynamic DNS 173
- has data traffic to forward 212
- 6.2 Setting Passwords 221
- New Security Policy screen 224
- 3. Refer to the 246
- 6.10.1.1 Available Protocols 251
- 6.11 Configuring VPN Tunnels 254
- Key Settings screen 264
- 6.11.4 Viewing VPN Status 268
- Details button 278
- 4. Refer to the 279
- Delete-> button 293
- Monitoring Statistics 299
- 7.1 Viewing WAN Statistics 300
- 7.2 Viewing LAN Statistics 304
- 7.3.1 Viewing WLAN Statistics 313
- 7.4.1.1 Retry Histogram 322
- 7.5.1 Viewing MU Details 325
- 7.5.2 Pinging Individual MUs 328
- CLI Reference 335
- 8.1 Connecting to the CLI 336
- 8.2 Admin and Common Commands 337
- AP51xx>admin>help 338
- AP51xx>admin>passwd 339
- AP51xx>admin>summary 340
- AP51xx>admin> 341
- AP51xx>admin> / 342
- AP51xx>admin>save 343
- AP51xx>admin>quit 344
- 8.3 Network Commands 345
- 8.3.1 Network LAN Commands 346
- Description: 347
- Syntax: 347
- Example: 347
- Related Commands: 350
- 8.3.2 Network WAN Commands 374
- 8.3.3.1 Network WLAN Commands 401
- 8.3.3.3 Network ACL Commands 422
- Descripton: 447
- 8.3.5 Network Router Commands 470
- 8.4 System Commands 476
- 8.4.2 System Access Commands 486
- Description: ) 491
- 8.4.4 System SNMP Commands 502
- 8.4.6 System Radius Commands 527
- Description: set 536
- 8.4.8 System Log Commands 555
- 8.5 Statistics Commands 572
- Configuring Mesh Networking 589
- 9.1.5 Normal Operation 594
- 9.3.1.1 Configuring AP#1: 609
- 9.3.1.2 Configuring AP#2 614
- 9.3.1.3 Configuring AP#3 615
- Repeater and a Client Bridge 619
- 9.3.2.1 Configuring AP#1 620
- 9.3.2.2 Configuring AP#2 620
- 9.3.2.3 Configuring AP#3 621
- Adaptive AP 629
- 10.1.1 Where to Go From Here 630
- 10.1.2 Adaptive AP Management 631
- 10.1.3 Types of Adaptive APs 631
- 10.1.4 Licensing 632
- 10.1.5 Switch Discovery 632
- 10.1.8 Configuration Updates 634
- 10.1.12 Adaptive Mesh Support 635
- 10.2.2 Extended WLANs Only 638
- 10.2.3 Independent WLANs Only 638
- Adaptive AP Pre-requisites 639
- 10.4.2 Switch Configuration 644
- Technical Specifications 655
- A.3 Radio Characteristics 658
- A.4 Antenna Specifications 659
- A.5 Country Codes 663
- Usage Scenarios 667
- Usage Scenarios 669
- B.1.1.3 DHCP Priorities 671
- B.1.2.1 BootP Options 673
- B.1.2.2 BootP Priorities 675
- Customer Support 687
- North American Contacts 688
- International Contacts 688
- Web Support Sites 689
- Additional Information 689
Verwandte Produkte und Handbücher für WLAN-Zugangspunkte Motorola AP-51XX
(4 Seiten)
(4 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.262 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern