Motorola MCU DG128 Betriebsanweisung

Engineering Technical Laboratory Rev. 6 MC68HC912/9S12 FLASH/EEPROM Programmer User’s Guide © ETL

is someOnly Bulksolved by this key a Backdoor Access Key disabled there is no possibilities to disable security. To solve this problem the second meth

6. FILE OPERATIONS This section describes basic rules working with files. Memory dump from Hex Editor (Buffer) can be load/save from/to hard disk. Al

7. ERRORS AND TROUBLESHOOTING This section describes most recently encountered problems, errors and fixing solutions.  Problem: LED D1 (see Figur

 Error Message: BDM Speed Auto Detection failed  Causes: This message can appear in In-Circuit programming interface if target MCU not connected co

 Error Message: Device still locked  Causes: This message can appear in On-Board programming interface when target MCU secured.  Solutions: Check

9. APPENDIX HC912/9S12 MCURESETBKGDVSSMODAMODBVDDGndECLKEXTALXTAL2...16 MHzLogic level on this pin must be “LOW”HC 9 12 Programm erP51246BKGDGndRES

123456789101112131415161718192080797877767574737271706968676665646362612122232425262728293031323334353637383940MC68HC912B3280 QFP605958575655545

12345678910111213141516171819202122232425262728112111110109108107106105104103102101100999897969594939291908988878685293031323334353637383940414

123456789101112131415161718192021222324252627281121111101091081071061051041031021011009998979695949392919089888786852930313233343536373839404142

6059575655545352515049484746455812456789101112131415163444342411820191780797776757473727170696867666578646362612122242526272829303132333435362

TABLE OF CONTENTS 1. PREFACE...

6059575655545352515049484746455812456789101112131415163444342411820191780797776757473727170696867666578646362612122242526272829303132333435362

123456789101112131415161718192080797877767574737271706968676665646362612122232425262728293031323334353637383940MC9S12 D64/DG64MC9S12 DT128/DG128/D

VRHVDDAPAD15/ AN15/ ETRI G1PAD07/ AN07/ ETRI G0PAD14/ AN14PAD06/ AN06PAD13/ AN13PAD05/ AN05PAD12/ AN12PAD04/ AN04PAD11/ AN11PAD03/ AN03PAD10/ AN

12345678910111213141516171819202122232425262728112111110109108107106105104103102101100999897969594939291908988878685293031323334353637383940414243

M0C0M/PU0M0C0P/PU1M0C1M/PU2M0C1P/PU3VDDM1VSSM1M1C0M/PU4M1C0P/PU5M1C1M/PU6M1C1P/PU7KWH0/PH0KWH1/PH1KWH2/PH2KWH3/PH3M2C0M/PV0M2C0P/PV1M2C1M/PV2M2C

1. PREFACE This manual will guide you through the installation and operation of the ETL MC68HC912/9S12 Programmer, referenced hereafter as the HC912

3. INSTALLATION AND USE The HC912-Programmer includes two LED’s and mode jumper (Figure 1). Color LED’s indicates programmer state and external pow

3.1 PROGRAMMER CHECK AND CONNECTION TO PC  Connect the power supply source to HC912-Programmer (an external 12 V DC power supply source is require

4. INTERFACE TYPES This section describes two interfaces, In-Circuit Programming (ICP) and On-Board Programming (OBP) of HC912-Programmer. 4.1 IN-C

5. WORKING WITH TARGET MCU This section contains overall information about Motorola MCUs supported by HC912-Programmer. When HC912-Programmer succes

 Load EEPROM/FLASH data from file (see Section 6.1) or enter data to Hex Editor. HC912-Programmer software. SH” button.  hat means that +5 voltag

 Select “Program Sequence” panel in HC912-Programmer software. Press “EEPR OM/FLASH” button. LED DregulatWhen compleIf some g removing the adaptor