Motorola LS1013 Bedienungsanleitung PDF herunterladen (Seite 3)

13. DON’T OVERREACH. Keep proper footing and

balance at all times.

14. MAINTAIN TOOLS WITH CARE. Keep tools sharp

and clean for best and safest performance. Fol-

low instructions for lubricating and changing

accessories.

15. DISCONNECT TOOLS before servicing; when

changing accessories such as blades, bits, cut-

ters, and the like.

16. REDUCE THE RISK OF UNINTENTIONAL START-

ING. Make sure switch is in off position before

plugging in.

17. USE RECOMMENDED ACCESSORIES. Consult

the owner’s manual for recommended accesso-

ries. The use of improper accessories may cause

risk of injury to persons.

18. NEVER STAND ON TOOL. Serious injury could

occur if the tool is tipped or if the cutting tool is

unintentionally contacted.

19. CHECK DAMAGED PARTS. Before further use of

the tool, a guard or other part that is damaged

should be carefully checked to determine that it

will operate properly and perform its intended

function - check for alignment of moving parts,

binding of moving parts, breakage of parts,

mounting, and any other conditions that may

affect its operation. A guard or other part that is

damaged should be properly repaired or

replaced.

20. DIRECTION OF FEED. Feed work into a blade or

cutter against the direction of rotation of the

blade or cutter only.

21. NEVER LEAVE TOOL RUNNING UNATTENDED.

TURN POWER OFF. Don’t leave tool until it

comes to a complete stop.

22. REPLACEMENT PARTS. When servicing use

only identical replacement parts.

23. POLARIZED PLUGS. To reduce the risk of elec-

tric shock, this equipment has a polarized plug

(one blade is wider than the other). This plug will

fit in a polarized outlet only one way. If the plug

does not fit fully in the outlet, reverse the plug. If

it still does not fit, contact a qualified electrician

to install the proper outlet. Do not change the

plug in any way.

VOLTAGE WARNING: Before connecting the tool to a

power source (receptacle, outlet, etc.) be sure the volt-

age supplied is the same as that specified on the name-

plate of the tool. A power source with voltage greater

than that specified for the tool can result in SERIOUS

INJURY to the user – as well as damage to the tool. If in

doubt, DO NOT PLUG IN THE TOOL. Using a power

source with voltage less than the nameplate rating is

harmful to the motor.

USE PROPER EXTENSION CORD. Make sure your

extension cord is in good condition. When using an

extension cord, be sure to use one heavy enough to

carry the current your product will draw. An undersized

cord will cause a drop in line voltage resulting in loss of

power and overheating. Table 1 shows the correct size to

use depending on cord length and nameplate ampere

rating. If in doubt, use the next heavier gage. The smaller

the gage number, the heavier the cord.

ADDITIONAL SAFETY RULES

USB036-2

DO NOT let comfort or familiarity with

product (gained from repeated use)

replace strict adherence to slide com-

pound saw safety rules. If you use this

tool unsafely or incorrectly, you can suf-

fer serious personal injury.

1. Wear eye protection.

2. Keep hands out of path of saw blade. Avoid con-

tact with any coasting blade. It can still cause

severe injury.

3. Do not operate saw without guards in place.

Check blade guard for proper closing before

each use. Do not operate saw if blade guard

does not move freely and close instantly. Never

clamp or tie the blade guard into the open posi-

tion.

4. Do not perform any operation freehand. The

workpiece must be secured firmly against the

turn base and guide fence with a vise during all

Table 1: Minimum gage for cord

Ampere Rating

Volts Total length of cord in feet

120 V 25 ft. 50 ft. 100 ft. 150 ft.

More Than Not More Than AWG

0 6 18 16 16 14

18 16 14 12610

10 12 16 16 14 12

12 16 14 12

Not Recommended

1 2 3 4 5 6 7 8 ... 75 76

Kommentare zu diesen Handbüchern

Keine Kommentare

Motorola LS1013 Bedienungsanleitung Seite 3

Kommentare zu diesen Handbüchern